Тойота РАВ4-Toyota RAV4 1. Car operation 2. Maintenance service 3. Engines 4. Cooling and air-conditioning systems 5. Fuel system and system of release of the fulfilled gases 6. Ignition system 7. The monitoring system and decrease in toxicity of the fulfilled gases 8. Coupling 9. A transmission 10. A kardannyj shaft and shaft of a drive of driving wheels 11. Brake system 12. A suspension bracket 13. A steering and a running gear 14. A body 15. An electric equipment    The general data    Technical characteristics    Electric chains    Check of the storage battery    Replacement of wires of the storage battery    Safety locks and the relay    Check and replacement of the relay of indexes of turn and the emergency light alarm system    Check of system of gymnastics    The generator    System of start-up of the engine    Replacement combined подрулевых switches    Replacement of the lock and the cylinder of the lock of ignition    Removal and installation of switches of the panel of devices    Removal and installation of a combination of devices    Check and replacement of the engine of a screen wiper    Radio receiver and dynamics    Aerial replacement    Check and repair of a heater of back glass    Replacement of lamps in headlights    Adjustment of light of headlights    Headlight replacement    Sound signal    Replacement of lamps накаливания    Check of a drive of external rear-view mirrors    Check of system of the cruise-control    Check стеклоподъемников with an electric drive    Check of system of the central blocking of locks    Drive podemno-sdvizhnoj roof panels    Safety pillows Electric equipment schemes Toyota RAV4>> Electric equipment>> Check and repair of a heater of back glass The heater of back glass consists of set of horizontally located conductors which have been raised dust on an internal surface has flown down. Insignificant ruptures of conductors can be restored without removal of back glass from the car. Check of a heater of back glass make as follows: For detection of rupture of a conductor of a heater of back glass include ignition, and the switch of a heater of back glass. Connect one щуп the voltmeter to positive contact of a heater, and the second to "mass" contact. If the voltmeter does not show pressure, check up the safety lock protecting an electric chain of a heater. If pressure is brought to heater contacts, execute following checks. Fig. 15.44. Use щупа the voltmeter which has been wrapped up by a foil, for detection of rupture of a conductor of a heater of back glass Connect one щуп the voltmeter to "weight" of the car, and the second щуп wrap up a foil and move a foil on a heater conductor (fig. 15.44 see). Fig. 15.45. Application of the voltmeter for detection of the broken off conductor of a heater of back glass Connect щуп the voltmeter in the centre of each conductor of a heater of back glass. If the voltmeter shows pressure nearby 5,5 In, the heater conductor means is serviceable. If the voltmeter shows pressure 0 in or 12 In, means, there is a rupture of a conductor of a heater (fig. 15.45). Fig. 15.46. Application of the voltmeter for detection of a place of rupture of a conductor of a heater of back glass For detection of a place of rupture of a conductor of a heater connect one щуп the voltmeter to the positive plug of a heater, and the second щуп move on a heater conductor from outside the negative plug of a heater. The point in which the pressure shown by the voltmeter, will fall about several volt to zero, will be is a place of rupture of a conductor of a heater (fig. 15.46). Before heater repair include it for some minutes. Repair of a heater of back glass make as follows: Restore rupture, using the special repair complete set. Smooth out conductors from two parties from rupture of a conductor and degrease them. With sticky tape stick glass from two parties of a conductor in a place of its rupture. Prepare glutinous current-carrying structure from the repair complete set. Put glutinous current-carrying structure to the place of rupture and the intact areas of each conductor on distance of 18 mm. Dry up glutinous current-carrying structure during 24 ч then remove a sticky tape.