Тойота РАВ4-Toyota RAV4
1. Car operation
2. Maintenance service
3. Engines
4. Cooling and air-conditioning systems
5. Fuel system and system of release of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. A transmission
   The general data
   Specifications
   Transmission repair
   The repair and adjusting works which are carried out on cars with a mechanical transmission
   The repair and adjusting works which are carried out on cars with an automatic transmission
      Diagnostics of an automatic transmission
      Replacement of sealing cuffs
      Check, adjustment and replacement of a cable of management throttle заслонкой
      Replacement and adjustment of a cable of the selector
      Replacement and adjustment of the switch of blocking of a starter (PNP)
      Check of system of blocking of the lever of the selector and the ignition lock
      Removal and installation of an automatic transmission on models with one leading bridge
      Removal and installation of an automatic transmission on all-wheel drive models
10. A kardannyj shaft and shaft of a drive of driving wheels
11. Brake system
12. A suspension bracket
13. A steering and a running gear
14. A body
15. An electric equipment
Electric equipment schemes




Toyota RAV4>> Transmission>> The repair and adjusting works which are carried out on cars with an automatic transmission>> Removal and installation of an automatic transmission on models with one leading bridge
Removal
Switch off ignition and disconnect a wire of "weight" from the storage battery.
Remove a cowl.
Remove a broad tank.
On models of release till 2001 loosen the a counternut also remove a cover of a cable from an arm of throttle knot. Disconnect a cable from sector throttle заслонки.
Remove a starter.
Mark and disconnect all electric sockets from a transmission.
Turn away a bolt of fastening of a wire of "weight".
Turn out bolts of fastening of a transmission accessible from above to the engine.
Establish over a motor compartment a cross-beam and a chain for an eye fix a transmission to a cross-beam.
Turn out a bolt of fastening of the left support of a transmission.
Loosen the nuts of fastening of power shafts to naves of forward wheels.
Tighten a lay brake and block back wheels. Lift a forward part of the car and establish it on support. Remove forward wheels.
Remove a mudguard of a motor compartment.
Turn away a nut of fastening of a cable of the selector and disconnect it from the lever of a choice of transfers on the forward party of a transmission.
Remove a clip and remove a cover of a cable from an arm on a transmission.
Merge трансмиссионную a liquid from a transmission.
Remove power shafts.
Remove a reception exhaust pipe.
Mark and disconnect all electric sockets accessible from below from a transmission.
Disconnect from a transmission the hoses going to an oil radiator. Close the ends of hoses plastic stoppers.
Turn out a bolt of fastening of the steering mechanism to the bottom cross-section beam. A soft wire fix steering transfer on a beam established across a motor compartment.
On models since 2001 remove заглушку, closing an aperture for access to the hydrotransformer, then a paint note position of the hydrotransformer and a drive plate.
On models 1996 and 1997 disconnect a cable of the selector from the bottom cross-section beam.
On models since 2001 disconnect earrings of the stabilizer of cross-section stability from the stabilizer.
Remove the bottom cross-section and longitudinal beams.

Fig. 9.29. An arrangement of bolts of fastening of a plate of rigidity


On models till 2001 turn out bolts and remove a rigidity plate (fig. 9.29).
On models till 2001 a paint note position of the hydrotransformer and a drive plate.
Turn out bolts of fastening of the hydrotransformer. For access to each subsequent bolt turn a cranked shaft of the engine in a direction of its working rotation for the central bolt of fastening of a pulley of a cranked shaft.
Support a transmission трансмиссионным a jack.
Turn out the remained bolts of fastening of a transmission to the engine, thus mark an arrangement of bolts as they have various length.
Take away a transmission from the engine and check up that the hydrotransformer is separated from a drive plate. Captures fix the hydrotransformer, lower and remove a transmission.
Installation
Installation make in sequence, return to removal taking into account the following.
Combine labels on the hydrotransformer and the drive plate, put before removal.
Fill in трансмиссионную a liquid in a transmission.
Adjust a selector cable, and a cable of management throttle заслонкой (on models till 2001).