Тойота РАВ4-Toyota RAV4 1. Car operation 2. Maintenance service 3. Engines 4. Cooling and air-conditioning systems 5. Fuel system and system of release of the fulfilled gases 6. Ignition system 7. The monitoring system and decrease in toxicity of the fulfilled gases 8. Coupling 9. A transmission    The general data    Specifications    Transmission repair    The repair and adjusting works which are carried out on cars with a mechanical transmission    The repair and adjusting works which are carried out on cars with an automatic transmission       Diagnostics of an automatic transmission       Replacement of sealing cuffs       Check, adjustment and replacement of a cable of management throttle заслонкой       Replacement and adjustment of a cable of the selector       Replacement and adjustment of the switch of blocking of a starter (PNP)       Check of system of blocking of the lever of the selector and the ignition lock       Removal and installation of an automatic transmission on models with one leading bridge       Removal and installation of an automatic transmission on all-wheel drive models 10. A kardannyj shaft and shaft of a drive of driving wheels 11. Brake system 12. A suspension bracket 13. A steering and a running gear 14. A body 15. An electric equipment Electric equipment schemes Toyota RAV4>> Transmission>> The repair and adjusting works which are carried out on cars with an automatic transmission>> Check, adjustment and replacement of a cable of management throttle заслонкой        THE NOTE These operations are made only on the models which were issued till 2001 Check Remove the case of the air filter and an air inlet branch pipe. Fig. 9.11. Distance measurement between an end face of a cover of a cable and a stopper on a cable of management throttle заслонкой: Х = 0–1 mm The assistant should press against the stop and keep an accelerator pedal, at this time measure distance Х (fig. 9.11) between edge of a cover of a cable and a stopper on a cable. If the distance is equal 0–1 mm then the cable is adjusted correctly, otherwise execute cable adjustment. Adjustment The assistant should press against the stop and keep an accelerator pedal, at this time loosen the a counternut and, rotating an adjusting nut, adjust position of a cover of a cable so that the distance between an end face of a cover of a cable and a stopper on a cable was in limits of 0-1 mm. Tighten a counternut, repeatedly measure distance between edge of a cover of a cable and a stopper on a cable and check up that throttle заслонка opens completely by pressing against the stop accelerator pedals. Replacement Loosen the a counternut also remove a cover of a cable from an arm of throttle knot. Disconnect a cable from sector throttle заслонки. Disconnect a cover of a cable from an arm on a transmission. Following on a cable downwards, define a place of its input in картер transmissions. Turn out a bolt supporting a cable at demanded level. Merge трансмиссионную a liquid from a transmission, remove the pallet and the filter. On models with one leading bridge of release with 1996 for 1998 turn out two bolts and remove an arm supporting pipes with трансмиссионной by a liquid. Disconnect pipes from a transmission. Fig. 9.12. An arrangement of bolts of fastening of a spring of a clamp on all-wheel drive models: And — a bolt, 14 mm; In — a bolt, 37 mm Fig. 9.13. An arrangement of bolts of fastening of the mechanical valve on all-wheel drive models: And — a bolt, 22 mm; In — a bolt, 37 mm On all-wheel drive models turn out two bolts and remove a clamp spring (fig. 9.12). On models with one leading bridge one bolt is established only. On all-wheel drive models turn out five bolts and remove the mechanical valve (fig. 9.13). On models of release with 1996 for 1998 disconnect all electric sockets from solenoids. On all-wheel drive models turn out a bolt, release a clip, and the big screw-driver take all eight oil tubes. Fig. 9.14. An arrangement of bolts which are necessary for turning out before extraction of a small oil tube on all-wheel drive models: And — a bolt, 39 mm; In — a bolt, 43 mm On all-wheel drive models turn out bolts, крепящие an electric socket, release a clamp and take a small oil tube (fig. 9.14). Fig. 9.15. An arrangement of bolts of fastening of the case of valves on models 2WD with 1996 for 1998: And — a bolt, 20 mm; In — a bolt, 30 mm; With — a bolt, 55 mm Fig. 9.16. An arrangement of bolts of fastening of the case of valves on models 2WD with 1998 for 2001: And — a bolt, 20 mm; In — a bolt, 28 mm; With — a bolt, 50 mm Fig. 9.17. An arrangement of bolts of fastening of the case of valves on models 4WD with 1996 for 2001: And — a bolt, 22 mm; In — a bolt, 32 mm; With — a bolt, 43 mm; D – 55 mm Fig. 9.18. A detachment of a cable of management throttle заслонкой from a cam on the case of valves Turn out bolts of fastening of the case of valves (fig. 9.15, 9.16, 9.17). Separate the case of valves from a transmission and disconnect a cable of management throttle заслонкой from a cam on the case of valves (fig. 9.18). Installation make in sequence, return to removal, taking into account the following. After transmission assemblage fill in in it трансмиссионную a liquid. If the new cable is established, fix on it a stopper as follows. Fig. 9.19. Stopper installation on a new cable of management throttle заслонкой Bend the cable end from outside throttle knot on radius of 200 mm. Extend a cable from a cover before occurrence of small resistance, then fix a stopper on a cable on distance of 0,8-1,5 mm from edge of a cover of a cable (fig. 9.19). Connect a cable to sector throttle заслонки and fix a cable cover on an arm, then execute adjustment.