Тойота РАВ4-Toyota RAV4
1. Car operation
2. Maintenance service
3. Engines
4. Cooling and air-conditioning systems
5. Fuel system and system of release of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. A transmission
   The general data
   Specifications
   Transmission repair
   The repair and adjusting works which are carried out on cars with a mechanical transmission
   The repair and adjusting works which are carried out on cars with an automatic transmission
      Diagnostics of an automatic transmission
      Replacement of sealing cuffs
      Check, adjustment and replacement of a cable of management throttle заслонкой
      Replacement and adjustment of a cable of the selector
      Replacement and adjustment of the switch of blocking of a starter (PNP)
      Check of system of blocking of the lever of the selector and the ignition lock
      Removal and installation of an automatic transmission on models with one leading bridge
      Removal and installation of an automatic transmission on all-wheel drive models
10. A kardannyj shaft and shaft of a drive of driving wheels
11. Brake system
12. A suspension bracket
13. A steering and a running gear
14. A body
15. An electric equipment
Electric equipment schemes





Toyota RAV4>> Transmission>> The repair and adjusting works which are carried out on cars with an automatic transmission>> Replacement of sealing cuffs
Leaks трансмиссионной liquids most often occur because of deterioration and ageing of sealing cuffs of power shafts or a speedometer drive (the gauge of speed). Replacement of these rings comes easy, as it is possible to replace them, without removing a transmission from the car.
Replacement of cuffs of power shafts
Sealing cuffs are located on each side transmissions, in places where power shafts incorporate to semiaxial gear wheels of differential. At liquid leak through sealing cuffs of power shafts lateral surfaces картера transmissions will be covered трансмиссионной by a liquid.
Lift the car on the lift.
Remove a power shaft.

Fig. 9.10. Removal of a sealing cuff of a power shaft


Edge of a screw-driver or stripper take out a cuff from a groove in картере differential, thus do not damage a groove surface (fig. 9.10).
Clear a groove for cuff installation.
Grease with engine oil an external surface and a working edge of a new cuff.
Tubular оправкой with external diameter, a bit smaller, than external diameter of a cuff, establish a cuff in a groove. Be convinced that the cuff is established without a warp.
Depth of installation of a sealing cuff concerning a groove end face in the differential case, mm:
– The right party on models with 1996 for 2001       –0,5... + 0,5
– A left-hand side on models with one leading bridge with 1996 on       2001 4,7... 5,7
– Both parties on all-wheel drive models with 1996 for 2001       –0,5... + 0,5
– Both parties on models with one leading bridge since 2001       –0,5... + 0,5
– The right party on all-wheel drive models since 2001       –0,5... 1,5
– A left-hand side on all-wheel drive models since 2001       –0,5... + 0,5
Establish a power shaft, thus do not damage a working edge of a sealing cuff.
Replacement of a sealing ring of the gauge of speed
In a transmission two gauges of speed are established: one supervises frequency of rotation of a primary shaft, another — a secondary shaft. They are fixed equally: a bolt supporting them at demanded level. Hermetic sealing is carried out by a sealing ring of round section.
For replacement of a sealing ring disconnect an electric socket of the gauge, turn out a bolt and remove the gauge of speed with картера transmissions.
Screw-driver edge remove a sealing ring from the gauge, establish a new sealing ring and grease it трансмиссионной with a liquid.
Installation make in sequence, return to removal.
Replacement of a cuff of a distributing box by all-wheel drive cars
Remove propeller a shaft.
Screw-driver edge take an old cuff, thus do not damage a surface of a groove for installation of a cuff and Slots a shaft.
Clear a groove for cuff installation.
Grease with engine oil a surface of a new sealing cuff.
Tubular оправкой with external diameter, a bit smaller, than external diameter of a cuff, establish a new cuff in a groove. Be convinced that the cuff is established without a warp on depth from 1,1 to 1,9 mm.
Grease Slots and the external surface of a flange contacting to a sealing cuff, and establish propeller a shaft.