Тойота РАВ4-Toyota RAV4
1. Car operation
2. Maintenance service
3. Engines
4. Cooling and air-conditioning systems
5. Fuel system and system of release of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. A transmission
10. A kardannyj shaft and shaft of a drive of driving wheels
11. Brake system
12. A suspension bracket
13. A steering and a running gear
14. A body
   The general data
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
      Processing of scratches of a body
      Repair of dents of a surface of a body
      Шпаклевка and body painting
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windscreen and motionless glasses
   Removal and cowl installation
   The lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation дефлектора a ventilating lattice
   Removal and installation of an upholstery of doors
   Removal and installation of glasses of doors
   Removal and installation стеклоподъемников
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Luggage space door
   Removal and installation of the central console
   Removal and installation of elements of furnish of the panel of devices
   Removal and installation of casings of a steering column
   Removal and installation of the panel of devices
   Removal and installation of seats
   Adjustment podemno-sdvizhnoj roof panels
15. An electric equipment
Electric equipment schemes

Toyota RAV4>> Body>> Repair of insignificant damages of a body>> Шпаклевка and body painting
At performance шпаклевочных works it is necessary to have wide flexible plastic or nylon шпатель for giving of smoothness of a surface шпаклевки. At performance of works on шпаклеванию a body adhere to following recommendations:
Level шпаклевку on the damaged site of a body so that to give it the demanded form and smoothness.
As soon as it was possible to achieve approximately demanded contour, stop to smooth down шпаклевку шпателем as at too long smoothing down it will start to harden, stick on шпатель and to roll down, therefore the surface will be damaged.
Put the subsequent, more thin layer шпаклевки, only after drying of the previous layer and so until level шпаклевки will not start to act slightly over a processed site.
After hardening шпаклевки its surplus remove a metal scraper or a file.
The further processing make, using at the first stage a coarse-grained emery paper, then fine-grained. An emery paper have on flat wooden бруске, differently it will be impossible to achieve an equal surface.
At a finishing stage of polishing it is necessary to moisten a waterproof emery paper with water periodically. It will give to the processed puttied surface special smoothness.
The puttied dent should appear surrounded on perimetre a layer of pure metal. For removal of a dust and fats wash out a processed site water and wipe degreasing means.
Raise dust on a site a thin layer of a light ground. It will help to reveal all defects admitted at processing in шпаклевке. Level them by means of a new layer шпаклевки and again зашкурьте a surface.
After that the repair area is ready to final painting.
Aerosol drawing of a paint should be spent in warm, dry, windless and easy atmosphere.
At painting carrying out indoors moisten a floor of a working platform with water for hit prevention in dust air. At colouring only one panel, other parts of a body should be covered from hit on them paints by the newspaper attached by a sticky tape.
Before first coat drawing carefully mix it, put on a trial surface and achieve that it laid down in regular intervals. Put a thick layer of a first coat for what put some thin layers.
Polish the grounded surface a waterproof emery paper. Thus do not forget сбрызгивать ground area water and periodically to moisten in water an emery paper.
Before the further painting dry up a processed site.
Put a paint coat a spray. The necessary thickness of a paint coat is reached by drawing of several thin layers.
Colouring begin from the centre of a processed surface and move to edges back and forth motions until all painted surface and area on distance about 20 mm round it will not be painted.
Protective film and newspapers remove later 10–15 минпосле drawings of last paint coat.
Give the chance to a fresh paint to harden within at least two weeks, then with the help обновителя a paint or thin abrasive polishing paste level edges of the painted area to level of an old paint.
Polish a surface.