Тойота РАВ4-Toyota RAV4
1. Car operation
2. Maintenance service
3. Engines
4. Cooling and air-conditioning systems
5. Fuel system and system of release of the fulfilled gases
6. Ignition system
7. The monitoring system and decrease in toxicity of the fulfilled gases
8. Coupling
9. A transmission
10. A kardannyj shaft and shaft of a drive of driving wheels
11. Brake system
12. A suspension bracket
13. A steering and a running gear
14. A body
   The general data
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windscreen and motionless glasses
   Removal and cowl installation
   The lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation дефлектора a ventilating lattice
   Removal and installation of an upholstery of doors
   Doors
   Removal and installation of glasses of doors
   Removal and installation стеклоподъемников
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Luggage space door
   Removal and installation of the central console
   Removal and installation of elements of furnish of the panel of devices
   Removal and installation of casings of a steering column
   Removal and installation of the panel of devices
   Removal and installation of seats
   Adjustment podemno-sdvizhnoj roof panels
15. An electric equipment
Electric equipment schemes




Toyota RAV4>> Body>> The lock and cable of opening of the lock of a cowl
       THE PREVENTION
Cars are equipped by safety systems (SRS), including pillows of safety and натяжители seat belts. Before work about gauges of blow, the panel of devices and a steering column disconnect at first negative, and then positive the plug from the storage battery and wait 2 minutes It will exclude unapproved disclosing of pillows of safety and operation натяжителей seat belts which can put physical injuries.

Removal of the lock of a cowl make следущим in the image:

Fig. 14.2. An arrangement of bolts of fastening of the lock of a cowl


Marker note position of bolts of fastening of the lock of a cowl (fig. 14.2 see). Turn out bolts and remove the lock from the forward cross-section panel.

Fig. 14.3. A detachment of a cover of a cable from the case of the lock of a cowl


Disconnect a cover of a cable from the case of the lock of a cowl and a cable from a lock latch (fig. 14.3).
Installation make in sequence, return to removal, taking into account the following: adjust lock position so that backlashes between a forward part of a cowl and wings were identical, and a rubber emphasis at cowl closing was slightly compressed.
Removal of a cable of opening of the lock of a cowl make следущим in the image:
In car salon remove the panel of an upholstery located under the panel of devices from outside of the driver.

Fig. 14.4. A detachment of a cable from the handle of opening of a cowl: And — a place of fastening of a cover of a cable; In — a place of fastening of a cable to the squeezing lever; With — a clamp


Lift the handle of opening of a cowl upwards and disconnect a cover of a cable from a handle arm, then disconnect a cable from the squeezing lever (fig. 14.4).
If squeezing the lever with the handle will be replaced, pull the handle outside and press downwards for removal from a clamp and its detachment from the panel of devices.
Adhere to a cable a thin long cord. Further the cord is required for retraction to the place of a cable of opening of a cowl.
In a motor compartment disconnect a cable and a cover of a cable from the cowl lock. Release a cable from clips on a forward cross-section beam and along a wing.
Extend a cable in a motor compartment, before cord occurrence, then untie a cord from an old cable and fix it on a new cable.
For a cord stretch a new cable through a partition of a motor compartment while it will not reach the handle of opening of a cowl, then untie a cord.
In car salon connect a cable to the squeezing lever, and a cable cover fix on a handle arm.
If at cable installation the condensing ring was displaced from a partition of a motor compartment, hand fingers establish it into place.
The further installation make in sequence, return to removal.